Cisco APIC

Hi Alessandro Rizzo, we have not received the additional information requested earlier from you in this issue 'Hi,

We have a Cisco APIC these run on UCS Chassis in case ours are the UCS C220 m5. 
Adding this device only brings back some basic info (ports). Its missing Storage, CPU and Memory along with environmental etc. 

I can see under our instance /mibs section there are the following mibs. 

CISCO-UNIFIED-COMPUTING-COMPUTE-MIB

CISCO-UNIFIED-COMPUTING-EQUIPMENT-MIB

CISCO-UNIFIED-COMPUTING-MEMORY-MIB

CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB

CISCO-UNIFIED-COMPUTING-STORAGE-MIB

https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/mib/c-series/b_UCS_Standalone_C-Series_MIBRef/b_UCS_Standalone_C-Series_MIBRef_chapter_01.html

Following above link states the above mibs can be used for these devices.  

I debugged the device can see how it matches on the OS and then what mib's are being applied. Below is that output, is it possible to get the Cisco APIC updated to add the above Mibs?'!

Issues without your response will be closed within 2 weeks.

I'm also having an issue detecting Cisco chassis but mine are via blades and the Cisco FI.  I believe the issue is that the analyzer for observium sees the switch OS print and goes "oh nexus, load the switching stuff" and it never gets to loading the compute MIBS even if it works fine on the chassis themselves as the rack chassis don't show nexus information they show the CIMC information.   I'll be happy to open another issue if this one doesn't apply to my scenario. 

Thanks, 

Debug

Probably trouble in snmp configuration on device.
Try to switch snmp v2 version..

Show snmp config from device (apic) without private fields (community/passwords/etc).

Hi Mike,

I've just been over the logs now I've seen failing on the following device is not responding to them...

CISCO-PROCESS-MIB
CISCO-ENTITY-SENSOR-MIB
CISCO-ENTITY-FRU-CONTROL-MIB 

That's cause it think these need to be the following as I put in the Jira and link the documentation which states these mibs should be used. 

CISCO-UNIFIED-COMPUTING-COMPUTE-MIB

CISCO-UNIFIED-COMPUTING-EQUIPMENT-MIB

CISCO-UNIFIED-COMPUTING-MEMORY-MIB

CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB

CISCO-UNIFIED-COMPUTING-STORAGE-MIB

I think this might of changed recently with the APIC Models and what MIBs are used. 

I'll do some digging tomorrow trying outside of obs polling the device to find out what works and doesn't to feedback. 

Cheers

Alessandro 

Hi Mike,

We've upgraded to latest no change.

I've attach the discovery as requested. 

Cheers

Alessandro 

Hi Mike

We have now updated the version of OBS running to 21.10.11678 (stable)

Hi, by first update your install (you use old revision):

There is a newer revision of Observium available!

Version 21.9.11575 (6th December 2021) is 210 revisions ahead.

After that make debug for all modules than (as I see os detected correctly):

./discovery.php -d -h <device>

Hi Mike, 

I've attached the debug you requested.  

We are currently running 21.5.11365

Its odd from your dev we don't see any status indicators or temperature appearing on the right hand side.

Cheers
Alessandro  

This is how I see your dump on my dev (partially):

Hi, as I see by your snmp dump, this device already correctly detected and already support all of this MIBs.
Which version of observium you use?

Please attach discovery debug for:

./discovery.php -d -m os -h <device>